1992 Mitsubishi Galant vr-4 2.4 4g63

Post Reply
Fastspec2
MegaSquirt Newbie
Posts: 5
Joined: Wed Mar 22, 2006 9:33 pm

1992 Mitsubishi Galant vr-4 2.4 4g63

Post by Fastspec2 »

1992 Galant vr-4
2.4 4g64 block eagle 100mm crank manly turbo rods, wiesco pistons, ported head, hks 272's
ms-2
msnse2 2.1.1, tuner studio
dual table and dual fuel 850cc injectors and 1200cc injectors (not yet sorted out) Boost control, open loop
25.8PSI 13.5* timing
gt35r
Ran the car and made 465HP with the above setup on pump gas. I have run the car to 8200 rpm (not on this msq or log, though the only changes were 8500 rpm rev limit) I believe the tune is pretty aggresive for pump gas but I get no sighns of detonation for another 2* or so.

So anyway, I'm pretty jazzed on how things are going. My goal is running the 1200's on e99 and seting up dual fuel for around 35-40PSI and hopefull 575 or so.
Will post up a dyno sheat when I get a chance to scan it and move it over.
You do not have the required permissions to view the files attached to this post.
Fastspec2
MegaSquirt Newbie
Posts: 5
Joined: Wed Mar 22, 2006 9:33 pm

Re: 1992 Mitsubishi Galant vr-4 2.4 4g63

Post by Fastspec2 »

Update

Got some more tuning done, car is really running well. Have setup idle advance, still working tward a idle control though so far with cold advance and idle advance setup the way I have it it runs 1300 rpm cold and tapers down to 800rpm hot so thats about right. The only time I see an idle control helping me out is after the first 20 seconds of startup. I actully pulled about 2 psi out of the boost control table as I was getting 102% duty cycle on the injectors. The last weak has been 20 degreese outside so its given me a chance to cold weather tune it really well.

Will keep updateing as I go.
Fastspec2
MegaSquirt Newbie
Posts: 5
Joined: Wed Mar 22, 2006 9:33 pm

Re: 1992 Mitsubishi Galant vr-4 2.4 4g63

Post by Fastspec2 »

I now have about 2000 miles on the tuned setup and I am really pleased. Good drivability, good power, and the best tuning and logging software you could ask for. I bumped my fuel pressure up to 60psi to get a bit more overhead and retuned accordingly. Now I'm about 90% duty and running 280KPA with no sighns of det or any other issues. As it sets, MS2 is working amazingly well. I think i will be needing to run a 4-5 bar setup when I switch over to e85. I am getting close to 3.0 bar with pump fuel.
HOODEY
MegaSquirt Newbie
Posts: 1
Joined: Thu Dec 01, 2005 4:20 pm

Re: 1992 Mitsubishi Galant vr-4 2.4 4g63

Post by HOODEY »

Need to know the signal generated from the Misu crank and cam sensors.
Fastspec2
MegaSquirt Newbie
Posts: 5
Joined: Wed Mar 22, 2006 9:33 pm

Re: 1992 Mitsubishi Galant vr-4 2.4 4g63

Post by Fastspec2 »

This is just me stashing an msq and datalog for another project. ITS NOT ANYTHING DSM RELATED
You do not have the required permissions to view the files attached to this post.
Post Reply