Mercedes 300CE-24v MS1 v3,0

Mercedes.
PUMPISH
MegaSquirt Newbie
Posts: 18
Joined: Fri Feb 15, 2008 2:15 pm
Location: Sweden stockholm
Contact:

Mercedes 300CE-24v MS1 v3,0

Post by PUMPISH »

Like I allways sad about K-jet...Yeah just send it to sibirijan!

Mercedes engines has allways been very high performans parts with very high quality and it make me cry why they choose K-jet for so long time!

If you realy love your car and stil have a K-jet, make very big differnce for your engine character and prosperous and it doesn not take many days to fix it if you have a good support.

Last week example:

Mercedes benz 300CE-24.

Standalone system instaling.

Megasquirt MS1-extra with stock dizzy ignition this time.
Parts we need:

Megasquirt ECU configuring for VR sensor and Distributor ignition.
(can even choose wasted spark and coil on plug)

Harness
2pcs relay
Fuel rail
Fuel fittings
Fuel regulator
6 of 250cc injectors
triggewheel 36-1
VR sensor
vr sensor fitting
TPS sensor
CLT sensor
IAT sensor
Air filter
Simple ignition coil (mercedes coil is too low ohm for the ecu)

Image

We start to replace the stock damper to triggerwheel 36-1 and fit the VR sensor

Image

Then its time to take some hand with K-jet...yeah ..

Image

gone....

Image
Image

Making the fuelrail

Image
Image
Image
Image
Last edited by PUMPISH on Sat Feb 16, 2008 6:07 am, edited 1 time in total.
PUMPISH
MegaSquirt Newbie
Posts: 18
Joined: Fri Feb 15, 2008 2:15 pm
Location: Sweden stockholm
Contact:

Post by PUMPISH »

Then make some fuelfittings to fit them the stock fittings and Fuel regulator

Image
Image

Then fix a little with throttel house to fit it with aftermarket TPS sensor

Image
Image
Image
Image

The plate for a wire..

Image

Airfilter pipe with IAT sensor and CLT sensor in the water pump

Image

ECU

Image
PUMPISH
MegaSquirt Newbie
Posts: 18
Joined: Fri Feb 15, 2008 2:15 pm
Location: Sweden stockholm
Contact:

Post by PUMPISH »

New harness

Image
Image

Robert supercharger 6,9 and me...
Image

Image

Trying go online

Image
Image

And the first start. Left to do is to fix the cables and mapping!

YouTube - MB 300-24v Megasquirt first start
PUMPISH
MegaSquirt Newbie
Posts: 18
Joined: Fri Feb 15, 2008 2:15 pm
Location: Sweden stockholm
Contact:

Post by PUMPISH »

Next one tired of K-jet and came to us today!
300CE-24v

Image
Image

Time to take some things away

Image
Image

Some new stuff

Image

This time we use different trigger by making 3 holes with M6 thread in the crankdamper och use 3 bolt as a triggerteeth. 120 degree between each bolt

4mm high aluminum distans and 4mm bolthead makes 8mm triggerpoints.

Image
Image
Image
Image

Hall sensor and bolton fitting

Image
PUMPISH
MegaSquirt Newbie
Posts: 18
Joined: Fri Feb 15, 2008 2:15 pm
Location: Sweden stockholm
Contact:

Post by PUMPISH »

Today was out of weldgas and cable but some things been done anyway.

Image

Fitting to IAT

Image

Making a thread

Image
Image

out of gas before finishing this pipe...

Image
Image
PUMPISH
MegaSquirt Newbie
Posts: 18
Joined: Fri Feb 15, 2008 2:15 pm
Location: Sweden stockholm
Contact:

Post by PUMPISH »

wireplate

Image

airfilterpipe with IAT

Image

Robban plays with cables

Image

Allmost done, just fix some cables...

Image

Image

First start

YouTube - Megasquirt first start (mercedes instal 3)
shisamo
MegaSquirt Newbie
Posts: 4
Joined: Sat May 10, 2008 2:46 pm

Re: Mercedes 300CE-24v MS1 v3,0

Post by shisamo »

Hi, Can I ask one question about the car that you using the 3 screw for the trigger ?
What coil you using for the ignition ? If I not remember wrong the OEM ignition is a CDI type ...

Thanks alot
PUMPISH
MegaSquirt Newbie
Posts: 18
Joined: Fri Feb 15, 2008 2:15 pm
Location: Sweden stockholm
Contact:

Re: Mercedes 300CE-24v MS1 v3,0

Post by PUMPISH »

shisamo wrote:Hi, Can I ask one question about the car that you using the 3 screw for the trigger ?
What coil you using for the ignition ? If I not remember wrong the OEM ignition is a CDI type ...

Thanks alot
yes you have absolutly right!
I use just some cheap coil that we have in sweden from the BILTEMA store and it works just fine.

It even works fine with a stock coil without overheating with lower dwell but I wanna be on the safe side and use normal biltema coil. It cost only 40 $

By the way I change the triggerwheel too becaurse I got many bolt on triggerwheel for both M103 and M104 engines so it feels better with a real triggerwheel then 3 bolts:)
shisamo
MegaSquirt Newbie
Posts: 4
Joined: Sat May 10, 2008 2:46 pm

Re: Mercedes 300CE-24v MS1 v3,0

Post by shisamo »

Thanks ffor the reply pumpish

But one thing I still cant figure it out. It is the rpm tachometer problem. Some people said connect the OEM tachometer directly to the coil. Some people said connect it to the MS ECU. Could you mind tell me which is the to do ?

Thanks alot
PUMPISH
MegaSquirt Newbie
Posts: 18
Joined: Fri Feb 15, 2008 2:15 pm
Location: Sweden stockholm
Contact:

Re: Mercedes 300CE-24v MS1 v3,0

Post by PUMPISH »

PUMPISH wrote:
shisamo wrote:Hi, Can I ask one question about the car that you using the 3 screw for the trigger ?
What coil you using for the ignition ? If I not remember wrong the OEM ignition is a CDI type ...

Thanks alot
yes you have absolutly right!
I use just some cheap coil that we have in sweden from the BILTEMA store and it works just fine.

It even works fine with a stock coil without overheating with lower dwell but I wanna be on the safe side and use normal biltema coil. It cost only 40 $

By the way I change the triggerwheel too becaurse I got many bolt on triggerwheel for both M103 and M104 engines so it feels better with a real triggerwheel then 3 bolts:)

if you run only 1 spark output and 1 coil then you just use minus on the coil to the signal.

If you use stock coil then you should have resistor on the signal pin about 1-1,5 ohm becaurse stock RPM gauge is prestty sensitive for low ohm
Post Reply