Vehicle: 1975 Jeep CJ-5
Engine: 258ci AMC Straight-6
Injection: TBI off of a chevy 350, 55lb injectors. They are a bit much for this engine, but it seems to run just fine.
Description: Currently running Megasquirt I on a v3 board, fuel only.
Status: Runs great, but the tune is nowhere near finished. I'm in the middle of installing edis-6.
Future Plans: Spark, WBo2, MS-II (financing is an issue, I'm a college student...)
Pre-EFI, Carter YF 1bbl
![Image](http://img243.imageshack.us/img243/5893/photo011320012bx3.jpg)
Adapter plate
![Image](http://img232.imageshack.us/img232/2654/photo011320013xy1.jpg)
Adapter plate - back side
![Image](http://lh5.ggpht.com/_uBHDYjcSmb8/SZ8o6l9LpSI/AAAAAAAAAhc/bQIozf_vAio/s512/Photo02151524.jpg)
CLT sensor, GM style
![Image](http://lh4.ggpht.com/_uBHDYjcSmb8/SZ8o6m_ivNI/AAAAAAAAAhk/BWLQHwH4PKQ/s512/Photo02151525.jpg)
4-wire narrow o2
![Image](http://lh4.ggpht.com/_uBHDYjcSmb8/SZ8o6vFu9SI/AAAAAAAAAh0/PRRBZb7t_YQ/s640/Photo02151610.jpg)
TBI mounted on intake
![Image](http://lh3.ggpht.com/_uBHDYjcSmb8/SZ8o63-k3HI/AAAAAAAAAh8/p3DlEQKo6MY/s640/Photo02151610_1.jpg)
TBI mounted on intake, sideshot
![Image](http://lh6.ggpht.com/_uBHDYjcSmb8/SZ8pIxibx5I/AAAAAAAAAiI/6NXUYq6TnDo/s640/Photo02160836.jpg)
TBI with the wiring rats nest
![Image](http://lh5.ggpht.com/_uBHDYjcSmb8/SZ8pI-SiEeI/AAAAAAAAAiQ/CsXphIJgyKw/s512/Photo02160836_1.jpg)
More hellish wiring
![Image](http://lh3.ggpht.com/_uBHDYjcSmb8/SZ8pJI_XUZI/AAAAAAAAAig/iKhs_x948Ko/s640/Photo02181704.jpg)
Wiring cleaned up, relay box mounted on firewall
![Image](http://lh4.ggpht.com/_uBHDYjcSmb8/SZ8pJAY0iXI/AAAAAAAAAio/XwbBcg2jnSM/s640/Photo02181705.jpg)
Another shot
![Image](http://lh6.ggpht.com/_uBHDYjcSmb8/SZ8pMim475I/AAAAAAAAAiw/MzRHtqBwjrs/s640/Photo02181705_1.jpg)
completely cleaned up, ready to run, as it is today.
![Image](http://lh3.ggpht.com/_uBHDYjcSmb8/Sl-jAk1pE0I/AAAAAAAAAn8/xJEoTCJxKtQ/s400/IMAG0118.jpg)
A mockup 36-1 mounted on the dampener
![Image](http://lh4.ggpht.com/_uBHDYjcSmb8/Sl-jPQ67o1I/AAAAAAAAAoU/CFLRjrzTp2I/s400/IMAG0174.jpg)
Final 36-1 mounted, cut from 1/4" scrap steel
![Image](http://lh3.ggpht.com/_uBHDYjcSmb8/Sl-jPk5V67I/AAAAAAAAAoY/zF1uPfTFFaU/s400/IMAG0175.jpg)
The VR in relation to tooth 6 (the tooth required for edis-6)
The dxf for the 36-1 trigger is at http://www.2shared.com/file/6721932/5db307c0/edis.html
The construction of my MS1 v3 board is at http://picasaweb.google.com/xeroOTG/Jee ... directlink
I have a bunch of other pictures of the install and the jeep at http://picasaweb.google.com/xeroOTG/
Ill update this thread when I finish the EDIS, and again when the WBO2 is installed.